ELECTRICAL POWER SYSTEM ANALYSIS

By | June 7, 2014

ELECTRICAL POWER SYSTEM ANALYSIS

17 – 20 Juni 2014

19 – 22 Agustus 2014

16 – 19 September 2014

7 – 10 Oktober 2014

18 – 21 November 2014

9 – 12 Desember 2014

Description

A Power System is predominantly in steady state operation or in a state that could with sufficient accuracy be regarded as steady state. In a power system there are always small load changes, switching actions, and other transients occurring so that in a strict mathematical sense most of the variables are varying with the time. However, these variations are most of the time so small that an algebraic, i.e. not time varying model of the power system is justified.

The purpose of this course is to develop a thorough understanding of power system analysis and design as well as the overall capabilities of Power Station. Class room discussion, and problem-solving has been designed to provide the analytical techniques necessary to solve a wide variety of practical problem.(pp)

 

Objectives

  • Verifying the adequacy of the power distribution system and it’s components.
  • Recognize coordination related disturbances and outages.
  • Collect the required data to perform a detailed coordination study.
  • Derive complete protective device settings for some of the simpler electrical power systems that are consistent with NEC requirements.

 

Outline

  1. Introduction to Industrial Power Systems
  2. Short Circuit Theory and Terminology
    • Effects of Short Circuits
    • Fault Current Sources
    • Machine Reactances
    • Fault Current Characteristics
  3. Electrical Equipment Ratings
  • Fuses
  • Circuit Breakers
  • Motor Starters
  • Conductors and Bus
  1. Balanced Fault Calculations
  2. Coordination Fundamentals
  • Procedures
  • Data Collection
  • Scaling Factors
  1. Plotting Time/Current Curves
  • Circuit Breakers
  • Fuses
  • Time Delay/Instantaneous Relays
  • Relay Coordination Intervals
  1. Equipment Protection and Coordination
  • NEC and ANSI/IEEE Criteria
  • Conductors (Low and Medium Voltage)
  • Transformers
  • Motors e. Conductors (Low and Medium)

 

Venue

Bandung (The Papandayan Hotel / The Aston Hotel / The Amaris Hotel )

In House Training:

Depend on request

“if there is demand for the implementation of training in another city we are ready to serve”

 

Participants

This course is intended for anyone who must perform calculations, provide settings or approve the work performed by others. The trainee should be a graduate engineer or have the equivalent practical work experience in electrical power systems.

Instructor

Tugino, ST, MT

 

Course fee

Biaya pelatihan sebesar Rp 8.500.000/peserta Non residensial. Khusus untuk pengiriman 3 peserta dari perusahaan yang sama, biaya pendaftaran sebesar Rp.8.000.000

 

Facilities

  • Training Module
  • Flash Disk contains training material
  • Certificate
  • Stationeries: NoteBook and Ballpoint
  • Backpack
  • Training Photo
  • Training room with Full AC facilities and multimedia
  • Lunch and twice coffeebreak every day of training
  • Qualified Instructor
  • Exclusive Gifts

Transportation for participants from hotel of participants to/from hotel of training (if minimal participants is 4 persons from the same company)

 

  1. FORMULIR PENDAFTARAN TRAINING
  2. Wajib diisi
  3. Jenis Pendaftaran Training
  4. PERSONAL DATA
  5. Wajib diisi
  6. Wajib diisi
  7. Wajib diisi
  8. Wajib diisi
  9. Sertakan Email yang Valid
  10. Wajib diisi
  11. PRE REGISTRATION DATA (Tidak Mengikat)
  12. Wajib diisi
  13. Pembayaran
  14. Pesan untuk Penyelenggara Training
 

cforms contact form by delicious:days

Leave a Reply

Your email address will not be published. Required fields are marked *